14 August 2026
How to Measure a Euro Cylinder Lock Before You Buy a Replacement
A step by step guide to measuring a euro cylinder lock so your replacement fits and sits flush with the handle plate.

Updated November 2026. Written by the WD Locks team, the lock shop of Watchdog Locksmiths, 397-399 Greenford Road, Greenford UB6 8RF. Our Watchdog 3 Star ALPS locks are BSI Kitemark 3 Star TS 007 tested, and installation is available from DBS-checked Watchdog locksmiths.
Key takeaways
- Euro cylinder sizes are two measurements, one for each side of the door, taken from the centre of the fixing screw to the end of the cylinder.
- Write down which side is the outside (key side) and which is the inside. A thumb turn always goes on the inside.
- Cylinders come in 5mm steps, so round to the nearest standard size.
- A correctly sized cylinder sits flush with the handle plate and never sticks out more than about 3mm. A cylinder that sticks out is easier to snap.
A euro cylinder that is the wrong length is one of the most common reasons a replacement does not fit. Too short and it will not reach the cam or handle properly. Too long and it sticks out of the door, where it can be gripped and snapped. Measuring takes five minutes and a ruler. This guide shows you how.
What you need
- A cross-head or flat-head screwdriver for the fixing screw.
- A ruler or a pair of callipers, in millimetres.
- Your existing key.
- A pen and paper to note the two measurements.
How to measure a euro cylinder: step by step
- Open the door fully. The fixing screw is in the edge of the door, level with the lock.
- Remove the fixing screw. Keep it safe: you will need it for the new cylinder.
- Turn the key about 45 degrees so the cam lines up with the case, then pull the cylinder out.
- Measure the outside. From the centre of the fixing screw hole to the end of the cylinder on the key side that faces outdoors.
- Measure the inside. From the centre of the screw hole to the end of the cylinder on the room side.
- Round to the nearest 5mm. Standard sizes go up in 5mm steps.
For example, a cylinder that measures 35mm on the outside and 45mm on the inside is a 35/45 cylinder, with an overall length of 80mm.
Measuring without taking the old cylinder out
You can measure the lock in place. Measure from the centre of the fixing screw to the face of the handle plate on each side. Choose the standard size that matches those measurements so the new cylinder sits flush. If the old cylinder was sticking out, do not copy its size: pick the size that leaves it flush with the handle plate, and never more than about 3mm proud.
Which side is inside and which is outside?
Standard cylinders are the same on both sides, but sizes are listed for each side, and the two sides are often different because of the door furniture. Our product pages list sizes as Inside / Outside, so a 30 Inside / 35 Outside cylinder is 30mm on the room side and 35mm on the door side. If you want a thumb turn, the thumb turn side is the inside. Read our guide to thumb turn cylinders.
Common mistakes
| Mistake | What goes wrong |
|---|---|
| Measuring from the end of the screw hole, not the centre | The cylinder ends up the wrong length |
| Swapping inside and outside | The cylinder does not sit flush on each side |
| Copying an old cylinder that sticks out | The new lock is easier to snap, not harder |
| Not rounding to a standard size | You order a size that does not exist |
Choose your lock
Once you have your measurements, choose the lock that suits your door:
- Watchdog 3 Star ALPS cylinder: a BSI Kitemark 3 Star TS 007 anti-snap euro cylinder with sizes for most doors.
- Watchdog 3 Star ALPS thumb turn: key on the outside, thumb turn on the inside.
- Watchdog 3 Star ALPS half cylinder 10/35: for garage doors, shutters and key switches.
Not sure? Our locksmiths can measure and fit it for you: see Watchdog Locksmiths lock replacement.
Frequently asked questions
What does 35/45 mean on a euro cylinder?
It means 35mm on one side of the fixing screw and 45mm on the other. The two numbers add up to the overall cylinder length, 80mm in this example.
Do I have to take the old cylinder out to measure it?
No. You can measure in place from the centre of the fixing screw to the face of the handle plate on each side, but taking the cylinder out is the most accurate way.
What if my size is not listed?
Euro cylinders come in 5mm steps. If your measurement falls between two sizes, choose the nearer size that leaves the cylinder flush, and contact us if you are unsure.
Can I fit it myself?
Yes, if you are comfortable with a screwdriver. Our guide to fitting a euro cylinder yourself walks you through it. Otherwise our locksmiths can fit it for you.
Ready to choose your cylinder?
Browse the WD Locks shop or contact us and we will help you choose the right lock and size.
Sources and further reading
Written by the Watchdog Locksmiths team. Questions about your door? Talk to an expert.

